Turbidity sensor TURBIMESS NG

​

TURBIMESS NG is an optical sensor measuring the reflected radiation arising from particles or fat droplets in liquid media.

Typical applications

• detection of product change
  (e.g. milk – cream – whey)

• continuous monitoring of e.g. milk fat content / quality inspection 

• monitoring of the cleaning agents’ pollution degree during CIP

• detection of filter breakdown

• detection of yeast and cloudy fruit juice

Features

• turbidity sensor with 2-wire 4….20 mA output

• process connections Clamp; Varivent; DIN 11851

• 2 individual programmable switch-points with status LEDs

• integrated LED display

• easy parametrizing with three push buttons

• compact hygenic design made in stainless steel

• 2 operating modes:
  - NTU mode (linear) for turbidities between 0 and 4.000 NTU 
  - 9 selectable support points for fat contents up to 30%

• temperature resistant long-term: 125°C /short-term 150°C

​_______________________________________________________________________________________________________

 

Conductivity Transmitters

​

Inductive conductivity / concentration transmitter INDUTEC

​

Features:

• hygienic sensor

• activation of up to four measuring ranges and temperature coefficients

• concentration measurement of caustic soda naoh and nitric acid HNO3

• fast-response temperature sensor- linear, natural water or specific characteristic

Description

The instrument is used for the measurement/control of conductivity or concentration in liquid media. It is particularly recommended for use in media where severe deposits of dirt, oil, grease or gypsum/lime precipitates are to be expected. The integrated temperature measurement enables fast and accurate temperature compensation, which is of particular importance when measuring conductivity. Additional functions, such as the combined changeover of measurement range and temperature coefficient, and a particularly robust conductivity probe, enable optimum application in CIP processes.

Two built-in switching outputs can be freely programmed to monitor limits for conductivity/concentration and/or temperature. It is also possible to assign alarm and control functions (dilution).

The instrument is operated from the membrane keypad and plain-text graphics display. The display can be read in a vertical or horizontal mounting position. Temperature signal 4...20mA is available as second parameter.

Typical areas of application: Food/beverage and pharmaceutical industries, product separation in the beverage industry, breweries and dairies, bottle cleaning plant, concentration control in electroplating and chemical processing plant, CIP systems, water and wastewater engineering, dosing of chemicals, leakage indication, in heating and cooling plant, and so on.

The inductive measurement method permits largely maintenance-free acquisition of the specific conductivity, even in the toughest media conditions.

Conductivity is measured by using an inductive probe. A sinusoidal a.c. voltage feeds the transmitting coil. Depending on the conductivity of the liquid to be measured, a current is induced in the receiver coil. This current is proportional to the conductivity of the medium.

_______________________________________________________________________________________________________​

​

Conductivity Transmitter
- Type Condutec -

​

Features

• measurement / control of conductivity or concentration in liquids

• available as compact unit or split version

• output for conductivity and temperature 4 - 20 ma

• measuring range programmable from  0… 500 ms/cm

• sensor can be sterilized up to 140°, 1 H

• various process connections are available, e.g. hygienic  design versions

Description

The conductivity transmitter Condutec is used for the measurement of conductivity or concentration in liquids, e.g. in CIP-lines or other processes in the beverage industry. High accuracy and resistance against contamination of the electrode are achieved by using 4 electrode conductivity cells.

The instrument can be operated directly and user-friendly at the graphic display. The switching output can be freely programmed; the Condutec is available either as a compact unit or split version (for strong vibrations or significant heat radiations).

​

​

​

              Please call or email our technical experts to discuss your requirements who will be happy to help.

  ​

                                                                        Tel 01704 505 333

                                                                     email sales@igeltd.co.uk

​